Winding wire SHTherm® 200
- Enamelled round cu.wire, thermo-resistant
- Insulated with theic-mod. polyesterimide
- Class 180
SHTherm® 200 is a highly thermo-resistant enamelled copper wire of heat performance class H. Its single coat insulation offers very good resistance to thermal overloads, thanks to its high thermoplastic flow and heat shock temperature. It also provides good resistance to commercial impregnating agents, impregnating resins, extrusion-coating agents, sealing resins, solvents and detergents. Furthermore the insulating enamel film distinguishes itself through high film elasticity and abrasion resistance. Sophisticated process technology and process setting ensure easy mouldability, very good elongation properties and low coefficients of friction, as well as good and constant dielectric insulation properties of these wires. In particular, resistance to dichlorodifluormethane (Freon) is to be emphasized. Thanks to the described wide range of excellent properties SH Therm® 200 is ideally suited for all standard applications in heat performance classes F and H, when sophisticated winding and draw-in technologies are used, as well as for use in refrigeration machines filled with Freon. SHTherm® 200 can be welded and mechanically connected but is not solderable.
Application
Control gears, electric motors, magnetic & ignition coils, refrigeration units, transformers
Standards
IEC / DIN EN 60317-08
NEMA MW 30-C
UL approved
Delivery forms
Grade 1: on request
Grade 2: on request
Technical data
Typical properties of enamelled copper wire 0.355 mm, with insulation film grade 1
| Property | Unit of measure | Set value | Actual value |
|---|---|---|---|
| Outer diameter with varnish | mm | min. 0.375 - max. 0.392 | as set value |
| Bare wire diameter | mm | 0.351-0.359 | as set value |
| Elongation and adhesion | mandrel diameter: 0.335 mm | 1 x d /10 % pre-elongation | |
| Scrape resistance | N | ≥ 3.050 | ≥ 4.500 |
| Pencil hardness of varnish | H | 3H - 4H | |
| Elongation at break | % | ≥ 27 | ≥ 33 |
| Coefficient of friction | µ | / | ≤ 0.140 |
|
(1) Due to the variety of individual applications we cannot make any generally binding commitments regarding the compatibility. We recommend testing compatibility with the materials being used. |
|||
| Property | Unit of measure | Set value | Actual value |
|---|---|---|---|
| Temperature index | °C | 180 | 190 |
| Cut through temperature (pre-heated block) | °C | 300 | ≥ 320 |
| Dielectric loss factor (bending point) | (°C) (tan δ) | / | ≥ 185 |
| Heat shock at 200 °C (no cracks in varnish coat after winding) | mendral diameter: 0.800 mm | 1 x d /10 % pre-elongation | |
| Solderability | no | no | |
|
(1) Due to the variety of individual applications we cannot make any generally binding commitments regarding the compatibility. We recommend testing compatibility with the materials being used. |
|||
| Property | Unit of measure | Set value | Actual value |
|---|---|---|---|
| Dielectric strength RT | kV | ≥ 2.3 (twist) | ≥ 2.5 (cylinder) |
| High voltage discontiniuties 750V | ≤ 10 on 30 m | ≤ 7 on 100 m | |
| Electrical conductivity | MS/m | 58 - 59 | ≥ 58.5 |
|
(1) Due to the variety of individual applications we cannot make any generally binding commitments regarding the compatibility. We recommend testing compatibility with the materials being used. |
|||
| Property | Set value | Actual value |
|---|---|---|
| Pencil hardness (storage in standard solvent ½ h / 60 °C) | min. H | 3H |
| Pencil hardness (storage in alcohol ½ h / 60 °C) | min. H | 3H |
| Resistance to commercial impregnants^(1) | / | yes |
| Resistance to commercial refrigerants (1) | / | yes |
| Resistance to dry transformer oils (1) | / | yes |
| Resistance to hydraulic oils (1) | / | yes |
|
(1) Due to the variety of individual applications we cannot make any generally binding commitments regarding the compatibility. We recommend testing compatibility with the materials being used. |
||